 |
 |
 |
 |
 |
|
| |
c o l o r c h a r t
•NSMS, Inc. Metallic finishes are available from stock at a moderate extra cost. NSMS, Inc. Copper Penny is a Non-Weathering Finish.
* Chips represent colors on 24 ga. galvanized steel.
NOTE: Because of variance in each viewer, colors may vary. Contact us at 404.298.9710 to receive a color chart or the actual color chip metal samples.
• Denotes colors available from stock.
* Indicates low gloss / low sheen colors.
|
|
STEEL |
ALUMINUM |
|
NSMS Standard |
24 ga. |
22 ga. |
.032 |
.040 |
.050 |
.063 |
.080 |
| Almond |
|
|
|
|
|
|
|
| Arcadia Green |
|
|
|
|
|
|
|
| Award Blue |
|
|
|
|
|
|
|
| Berkshire Blue |
|
|
|
|
|
|
|
| Bone White |
|
|
|
|
|
|
|
| Burgundy |
|
|
|
|
|
|
|
| Cardinal Red |
|
|
|
|
|
|
|
| Charcoal |
|
|
|
|
|
|
|
| Colonial Red |
|
|
|
|
|
|
|
| Dark Bronze |
|
|
|
|
|
|
|
| Forest Green |
|
|
|
|
|
|
|
| Granite |
|
|
|
|
|
|
|
| Hartford Green |
|
|
|
|
|
|
|
| Hemlock Green |
|
|
|
|
|
|
|
| Interstate Blue |
|
|
|
|
|
|
|
| Mansard Brown |
|
|
|
|
|
|
|
| Matte Black |
|
|
|
|
|
|
|
| Medium Bronze |
|
|
|
|
|
|
|
| Military Blue |
|
|
|
|
|
|
|
| Muskret Gray |
|
|
|
|
|
|
|
| Patina Green |
|
|
|
|
|
|
|
| Sandstone |
|
|
|
|
|
|
|
| Sierra Tan |
|
|
|
|
|
|
|
| Slate Gray |
|
|
|
|
|
|
|
| Stone White |
|
|
|
|
|
|
|
| Teal |
|
|
|
|
|
|
|
| Terra Cotta |
|
|
|
|
|
|
|
| NSMS |
|
|
|
|
|
|
|
| Aged Copper |
|
|
|
|
|
|
|
| Champagne |
|
|
|
|
|
|
|
| Copper Penny |
|
|
|
|
|
|
|
| Silver |
|
|
|
|
|
|
|
| Weathered Zinc |
|
|
|
|
|
|
|
| Zinc |
|
|
|
|
|
|
|
INSTALLATION:
NSMS, Inc. materials can be cut, formed, nailed, screwed, or riveted using hand or power tools. Fabricate and install in accordance with drawings and normal sheet metal practices using hand or power tools. Keep cutting edges sharp, clean, and properly aligned. Exercise care during fabrication and installation to avoid damage.
MAINTENANCE:
Maintenance is not required. This finish is a member of the Teflon® family, and is self-cleaning. If cleaning is desired, it can be washed with a mild soap and water followed by a clean-water rinse.
SAMPLES:
These color reproductions are as accurate as modern printing technology will permit. Free material samples are available on request.
TEXTURES:
NSMS, Inc. materials are available with a smooth texture or a standard E-5 stucco embossed pattern available at an extra cost.
*LOW GLOSS / LOW SHEEN:
This finish is a full 70% Kynar 500® / Hylar 5000® finish, but is formulated in a low gloss / low sheen in order to minimize the appearance of oil-canning.
TECHNICAL DATA FOR KYNAR 500® / HYLAR 5000® COATING:
- Life Expectancy - 20 years exposure - Chalk: rating of 8 or better. Color: ≤5ΔE (Hunter Units) change.
- Accelerated Weathering - (ASTM G-23 Type EH) 5,000 hours - Chalk: rating of 8 or better. Color: ≤5ΔE (Hunter Units) color change.
- Humidity Resistance - (ASTM 2247) 1,000 hours - No change in pencil hardness.
- Salt Spray Resistance - (ASTM B 117) - 2,000 hours for Aluminum, creepage at scribe ≤1/32", no blisters. 1,000 hours for hot dipped Galvanized, creepage at scribe ≤1/8", few #8 blisters.
- Chemical / Acid Pollution Resistance - (ASTM D 1808) - Pass.
- Solvent Resistance - (NCCA procedure 11-18, no comparable ASTM test) - Pass.
- Formability - (ASTM D 3281 and ASTM D 1737) - Can be formed without film fracture using normal metal shop practices to a 1 to 2-T bend radius.
- Hardness - (ASTM D 3363) - ≥F pencil hardness.
- Gloss - 30 ± 5 at 60° (low gloss / sheen available).
- Abrasion Resistance - (ASTM D 968) - Coefficient of 65 ± 10.
- Adhesion - (ASTM D 3359 and NCCA procedure No. 11 - 5) - Pass.
- Impact Resistance - (ASTM D 2794 and NCCA Technical Bulletin No. 11 - 6) - 70 inch/bbs., no tape pick-off.
|
|
| |
|
|
